(EST)_MahviaDeTyrk

01-02-2010, 11:32 AM

Ook - as You wish :cool:

It's car sellers picture - so it come to me - 2006
Totally stock Nissan Patrol 160 SWB Hardtop from 1984
Engine SD33T (its I6 3,3 Liter turbodiesel - same as IH Scout II and Jeep CJ10)
5 speed manual
31x10,5 AT tires at C200 front and H233 rear axle
http://y.delfi.ee/orig/71185/3196017_nd8gjA.jpeg

Few mounts later with 33x12 muddyes allready - one of first testdrives
http://y.delfi.ee/orig/71185/3195957_DM9qkV.jpeg

Continues :wave:

Alpine Spirit

01-02-2010, 02:55 PM

Sweeeeeeeeeeeet Truck

Cowboy Dave

01-02-2010, 04:25 PM

The front clip looks so much like an 80's Bronco II

JBDevega

01-02-2010, 08:27 PM

thats awesome

(EST)_MahviaDeTyrk

01-03-2010, 02:31 AM

So ... after that I was looking around what mods to do :bounce:

Some possibilitys
http://y.delfi.ee/norm/20096/2602677_64x93C.jpeg

http://y.delfi.ee/norm/20096/2602661_EG693O.jpeg

http://y.delfi.ee/norm/20096/2603389_xdZKOQ.jpeg

http://y.delfi.ee/norm/20096/6084839_tEn8PE.jpeg

So many choices :crazy:

To be continued :wave:

(EST)_MahviaDeTyrk

01-04-2010, 05:03 AM

Around one year later - started some bodywork + front and rear corners are cutted
There are placed small passenger car coils behind frame and leaf to restore leaf curve and for bump stop (they lift my old weak leafs around 4'' - and 2'' bodylift)
http://y.delfi.ee/norm/71185/8336977_gd6nGp.jpeg

And mud pictures :driving:
http://y.delfi.ee/norm/71185/8336981_Ed1nUN.jpeg
http://y.delfi.ee/norm/71185/8336983_Awt8s0.jpeg

To be continured :wave:

(EST)_MahviaDeTyrk

01-08-2010, 05:27 AM

Side bars made
http://y.delfi.ee/orig/72055/3251245_Sz4oR1.jpeg
http://y.delfi.ee/orig/72055/3251241_zDm7yc.jpeg

To be continured :wave:

(EST)_MahviaDeTyrk

01-09-2010, 08:20 AM

Reversing sharkles and moved front axle 2'' forvard
http://y.delfi.ee/norm/159599/8367811_VlanzR.jpeg
http://y.delfi.ee/norm/159599/8367809_cbYiQd.jpeg
http://y.delfi.ee/norm/159599/8367813_Pu131k.jpeg
http://y.delfi.ee/norm/159599/8367815_w7u28X.jpeg
http://y.delfi.ee/norm/159599/8367817_hwW4gA.jpeg
http://y.delfi.ee/norm/159599/8367819_lsFENZ.jpeg
http://y.delfi.ee/norm/159599/8367821_zsxOjW.jpeg
http://y.delfi.ee/norm/159599/8367823_4uvg0I.jpeg
http://y.delfi.ee/norm/159599/8367825_LFuj5d.jpeg
http://y.delfi.ee/norm/159599/8367827_ZeLI8Z.jpeg
http://y.delfi.ee/norm/159599/8367829_gbPKHj.jpeg
http://y.delfi.ee/norm/159599/8367831_0Khz4p.jpeg
http://y.delfi.ee/norm/159599/8367833_tmbTqj.jpeg
http://y.delfi.ee/norm/159599/8367835_MWBjLl.jpeg
http://y.delfi.ee/norm/159599/8367837_yJP4ga.jpeg
http://y.delfi.ee/norm/159599/8367839_Ry2ozO.jpeg
http://y.delfi.ee/norm/159599/8367841_SBoHFR.jpeg
http://y.delfi.ee/norm/159599/8367845_zBYzIB.jpeg
http://y.delfi.ee/norm/159599/8367849_k4NIqW.jpeg
http://y.delfi.ee/norm/159599/8367851_waYrRS.jpeg

And results
http://y.delfi.ee/norm/159599/8367853_ZiTYMo.jpeg
http://y.delfi.ee/norm/159599/8367855_spvINH.jpeg
http://y.delfi.ee/norm/159599/8367857_FPUrya.jpeg

To be continured :wave:

(EST)_MahviaDeTyrk

01-14-2010, 07:53 AM

New bullbar

http://y.delfi.ee/orig/160493/8404161_TpsFwB.jpeg
http://y.delfi.ee/orig/160493/8404165_ZBKLLO.jpeg
http://y.delfi.ee/orig/160493/8404167_H5wez3.jpeg
http://y.delfi.ee/orig/160493/8404171_4UI8ni.jpeg
http://y.delfi.ee/orig/160493/8404169_UQCaMl.jpeg
http://y.delfi.ee/orig/160493/8404175_tUPFNe.jpeg
http://y.delfi.ee/orig/160493/8404183_ZDtGP5.jpeg
http://y.delfi.ee/orig/160493/8404177_vLxry1.jpeg
http://y.delfi.ee/orig/160493/8404179_DXrdYD.jpeg
http://y.delfi.ee/orig/160493/8404185_wQ83EA.jpeg

To be continued :wave:

Alex Topousis

01-14-2010, 03:03 PM

So you have coils and leafsprings? Interesting concept

cuong nguyen

01-14-2010, 04:49 PM

Looks good! Interesting helper spring concept.

(EST)_MahviaDeTyrk

01-15-2010, 01:06 PM

So you have coils and leafsprings? Interesting concept

Yapp - leafs and coils
Leafs must be very weak or very soft - and coils are taken from very small passenger car - then it works almost like coil suspension
Coil helps to lift soft coils and is a pump stop too there - many less possibilitis to brake leafs

It leaf/coil spring strength is well balanced it flexes too ok - and can flex better then mine with SOA (higher roll center)
flex is not a primary request on these car - it's swamper
One little bit older picture
http://y.delfi.ee/orig/160493/8411805_JLqVzr.jpeg

To be continued :wave:

(EST)_MahviaDeTyrk

01-18-2010, 10:57 AM

With reversing shackles castor correction was needed
http://y.delfi.ee/norm/160493/8404159_JDucKk.jpeg

Made front diff guard
http://y.delfi.ee/orig/160493/8431739_GF9sd3.jpeg

Just few mud pictures to ending build year 2008:bannana:

http://y.delfi.ee/orig/160493/8431895_SdTxCQ.jpeg
http://y.delfi.ee/orig/160493/8431891_bsof1u.jpeg

continued in 2009 :wave:

JeffW

01-18-2010, 11:05 AM

Nice pics. Does the water get into all your drivtrain?

(EST)_MahviaDeTyrk

01-18-2010, 11:16 AM

Nice pics. Does the water get into all your drivtrain?

Not really - if to drive not stay there :cool:
Nissan C200 and H233B live front axles are are with normal water resistance - not like Dana bullshit
Gearbox and transfer are waterproof

These time was little bit water on engine (snorkel needed)
http://y.delfi.ee/norm/160493/8431999_oYpUpa.jpeg

(EST)_MahviaDeTyrk

02-05-2010, 10:10 AM

Found and installed 5,14 diff gears from 260 series Patrol
And installed them in front and rear with tight LSD diff (one extra friction disk)
http://y.delfi.ee/orig/163405/8552943_uCdAZV.jpeg

And made strong panzer
http://y.delfi.ee/orig/163405/8552945_qnvhL5.jpeg
http://y.delfi.ee/orig/163405/8552947_cqoLbv.jpeg
http://y.delfi.ee/orig/163405/8552941_jHnKxx.jpeg

:wave:

(EST)_MahviaDeTyrk

02-09-2010, 09:21 AM

Cooler protection
http://y.delfi.ee/orig/163911/8581077_XrtbNV.jpeg
http://y.delfi.ee/orig/163911/8581079_kXPMwp.jpeg
http://y.delfi.ee/orig/163911/8581081_dfu6xP.jpeg
http://y.delfi.ee/orig/163911/8581073_CruLww.jpeg

Just pics too
http://y.delfi.ee/orig/163911/8581075_kcLC9H.jpeg

:wave:

itsme1738

02-09-2010, 05:01 PM

very nice!

(EST)_MahviaDeTyrk

02-21-2010, 10:22 AM

Little play with epoxide for extra gauges :crazy:
http://y.delfi.ee/norm/165403/8654257_u6yDDY.jpeg
http://y.delfi.ee/norm/165403/8654259_C9DM1X.jpeg
http://y.delfi.ee/norm/165403/8654255_9h7EkV.jpeg

:wave:

(EST)_MahviaDeTyrk

03-10-2010, 10:26 AM

Now i can use mechanical oil pressure gauge with on-off type switch for warning lamp

http://y.delfi.ee/orig/165403/8765539_rRlhye.jpeg

One mud pic too :cool:
http://y.delfi.ee/orig/165403/8765557_OEN51d.jpeg

:wave:

(EST)_MahviaDeTyrk

03-19-2010, 02:00 PM

Made new gearbox/transfer mounts (OEM ones are too weak)

http://y.delfi.ee/orig/163405/8815889_G4mktN.jpeg
http://y.delfi.ee/orig/163405/8815885_I0dsfC.jpeg
http://y.delfi.ee/orig/163405/8815879_pELaH0.jpeg

:wave:

(EST)_MahviaDeTyrk

03-30-2010, 08:13 AM

Changed PTO shaft side from front to rear - because wanna install mechanical winch into center of car (better weight balance)

http://y.delfi.ee/orig/169527/8885585_QuLTBf.jpeg
http://y.delfi.ee/orig/169527/8885587_IKj45Z.jpeg
http://y.delfi.ee/orig/169527/8885583_qlFI4p.jpeg

:wave:

Chainsaw

03-30-2010, 05:14 PM

WOW! lots of extra guages! How will you run the cable for you winch if its mounted mid car? Through the floor and next to the engine?

Packman5280

03-30-2010, 05:47 PM

there is no cable, just a lever, like a shifter.

pto's are cool.

Chainsaw

03-31-2010, 05:07 PM

The cable that pulls the truck...

Packman5280

03-31-2010, 06:07 PM

lol, good point, hadn't thought of that. although i once winched a car that was behind me by looping through a snatch block then back under the truck to the car behind me. it worked cuz my truck was so tall and the car was really low.

(EST)_MahviaDeTyrk

04-02-2010, 11:32 AM

How will you run the cable for you winch if its mounted mid car? Through the floor and next to the engine?

Really - I Don't know exactly :crazy:
I have newer seen truck with center mounted winch - but look little bit earlier post where are gearbox/transfer case mounts (there is a pic where is gearbox side with PTO place cover) - I think dawn the floor beside gearbox and engine is marginal space for cable (exhaust piping must be removed/rebuilded)
I wanna install half of winch trough floor into cabin behind driver seat - so I can see from mirror it and I can switch free running from driver position

Started winch mount welding
http://y.delfi.ee/orig/169835/8900261_N68gnM.jpeg
http://y.delfi.ee/orig/169835/8900259_PGa7BB.jpeg
http://y.delfi.ee/orig/169835/8900257_SIIVzs.jpeg

:wave:

(EST)_MahviaDeTyrk

04-06-2010, 12:15 PM

Ook - winch is now mostly cleaned and rebuilded
It's Toyota mech winch 33/1 Worm gear
I made winch drum 60mm larger and ventilation too

http://y.delfi.ee/orig/169835/8924691_KvCBYO.jpeg
http://y.delfi.ee/orig/169835/8924693_gjJNY7.jpeg
http://y.delfi.ee/orig/169835/8924689_yBrUGx.jpeg

:wave:

(EST)_MahviaDeTyrk

04-15-2010, 11:13 AM

Finally my snorkel piping is ready to install
4'' stainless pipes (fck they are huge)- external ones are coated with Line-x ( http://www.line-x.com/ ) so they don't shine :cool:

http://y.delfi.ee/orig/171281/8973863_xJxZyl.jpeg
http://y.delfi.ee/orig/171281/8973867_dEpaVQ.jpeg

Small pipe is for future propane injection
http://y.delfi.ee/orig/171281/8973865_U05yFL.jpeg

big K&N Pre-Cleaner is going outside of car
http://y.delfi.ee/orig/171281/8973869_ilc0NV.jpeg
http://y.delfi.ee/orig/171281/8973873_uvHgnE.jpeg

:wave:

soccerbrace

04-15-2010, 01:38 PM

Holy crap! Is that a specific kit for your truck, or did you do that? I ask because they appear mandrel bent, and I think it looks like it will work very well.

MisterTinkle

04-15-2010, 05:02 PM

Very nice! :bowdown:

Packman5280

04-15-2010, 05:57 PM

dats a purdy snorkel, most i see are plastic. looks good.

(EST)_MahviaDeTyrk

04-16-2010, 12:27 AM

Is that a specific kit for your truck, or did you do that?

Home made

soccerbrace

04-16-2010, 07:25 AM

Sweet man! Good work. Can't wait to see it installed. I had a snorkel once but realized I never used, so I sold it.

(EST)_MahviaDeTyrk

04-21-2010, 12:08 PM

I bent my Patrols front axle housing again - So I try to laminate new one little bit and try to remove helper coils and use leafs with coilovers

http://y.delfi.ee/orig/171991/9012253_B6abUa.jpeg
http://y.delfi.ee/orig/171991/9012255_razxRG.jpeg
http://y.delfi.ee/orig/171991/9012257_91FS6s.jpeg

Hope coliover in these position helps to underbear axle end
http://y.delfi.ee/orig/171991/9012261_UuNvNu.jpeg

Shimmed LSD and guard
http://y.delfi.ee/orig/171991/9012259_NMeNw3.jpeg
http://y.delfi.ee/orig/171991/9012263_vTtkfz.jpeg

:wave:

(EST)_MahviaDeTyrk

05-10-2010, 10:26 AM

There You can see how is front axle binded
http://y.delfi.ee/orig/171991/9143727_2XJC29.jpeg

Now new axle tube is installed but no coilovers jet - so I don't know jet how it works :rolleyes:

Try to reinforce CV's with heat seated steel rings
rings are ready for installation - material is Stal-45 http://www.multistal.pl/go.live.php/EN-H351/4510530.html - I really don't know what these is in other countries
http://y.delfi.ee/orig/171991/9143729_bqyLIE.jpeg

And I started to build hydraulic handbrake
OEM one is mech drum brake behind transfer - I wanna rebuild it into disk and hydraulic

Inside part is almost ready - used Patrol clutch master cilinder
http://y.delfi.ee/orig/171989/9143725_L4eubv.jpeg
http://y.delfi.ee/orig/171989/9143723_bwv7RE.jpeg

:wave:

JeffW

05-10-2010, 07:28 PM

Wow!

itsme1738

05-10-2010, 08:17 PM

yea......just wow!

(EST)_MahviaDeTyrk

05-31-2010, 01:39 PM

Internal part of hydraulic handbrake is finished :bannana:

http://y.delfi.ee/orig/171989/9299367_yxdTmv.jpeg
http://y.delfi.ee/orig/171989/9299365_vl9P7r.jpeg

:wave:

(EST)_MahviaDeTyrk

06-13-2010, 11:14 AM

CV's are ready - heat seated rings (-0,3mm - maybe it's too small seat - installing was too easy I think - if I break these, next will do -0,5mm) welded from three points and turned into size
OEM external size = 90mm
Now 96mm (ring wall 3mm)

http://y.delfi.ee/orig/171991/9403463_ElEZie.jpeg

:wave:

(EST)_MahviaDeTyrk

10-04-2010, 12:35 PM

I have not written long time nothing - because mostly have done nothing

but

Rebuilded brake caliper for hydraulic handbrake
taken from Opel Omega B - rear one - like these because there are no moving parts except pistons - 2x 35mm pistons :p
http://y.delfi.ee/orig/169833/10278439_pjTPzq.jpeg

And made caliper mounting
http://y.delfi.ee/orig/169833/10278437_nWeuoA.jpeg

:wave:

Packman5280

10-04-2010, 12:47 PM

cool little bracket there...

(EST)_MahviaDeTyrk

10-12-2010, 01:16 PM

Wanna move rear axle back around 4'' - so I cant use OEM fuel tank soon any more
I install these one inside the truck (I hope it's just temporary one and I can make custom stainless fuel tank soon)
Taken from soviet truck UAZ-469
Its 42 L - OEM Patrol one is 89 L
It was old one - so cleaned inside and out and painted and made some little mod's too
http://y.delfi.ee/orig/192187/10327515_JfgEu1.jpeg

And custom mounting
http://y.delfi.ee/orig/192187/10327517_jD9JID.jpeg

:wave:

Chainsaw

10-12-2010, 05:40 PM

:beermug: Always enjoy your modification posts. How's that hand brake working?

(EST)_MahviaDeTyrk

02-28-2011, 11:58 AM

Fuel tank finally installed
http://y.delfi.ee/orig/192187/10963243_K00lPy.jpeg
And new fuel lines are all now inside of body
http://y.delfi.ee/orig/192187/10963241_o0QdV7.jpeg

:wave:

T-Ray

02-28-2011, 12:03 PM

Very cool. What is that tank out of and how many gallons?

ETA: nevermond, didn't read the 1st couple posts *doh*

(EST)_MahviaDeTyrk

03-13-2011, 01:36 PM

How's that hand brake working?

It's installed (today) - but don't know how well it works - not tested jet

http://y.delfi.ee/orig/171989/11024549_yDtp32.jpeg
http://y.delfi.ee/orig/171989/11024551_O09JGW.jpeg
http://y.delfi.ee/orig/171989/11024547_V6kB1a.jpeg

:wave:

Creek

03-13-2011, 01:46 PM

nice work!

itsme1738

03-13-2011, 05:08 PM

after looking at all those pics again i just saw that he moved his mirrows to the hood
looks good

(EST)_MahviaDeTyrk

03-26-2011, 01:30 PM

after looking at all those pics again i just saw that he moved his mirrows to the hood
looks good

Jep - You are right - all other mod's are secondary

Original view into engine first end = I think there can be too less vee-belts
http://y.delfi.ee/orig/206247/11079583_ryOTxf.jpeg

So.....
I made some new belt pulleys :crazy:
left to right
OEM water pump one - new water pump pulley - new power steering pulley - and new crankshaft one
http://y.delfi.ee/orig/206247/11079581_zI2jsb.jpeg

Removing OEM crankshaft pulley is real pain - so... I made new one with special tool for that
http://y.delfi.ee/orig/206247/11079587_aVCmf4.jpeg

One day I will install them all

:wave:

Chainsaw

03-26-2011, 02:42 PM

Nice work dude! And now you will have extra Vs to run accessories off of. Like an air compressor.

(EST)_MahviaDeTyrk

03-31-2011, 01:10 AM

21.04.2010 I said
I bent my Patrols front axle housing again - So I try to laminate new one little bit and try to remove helper coils and use leafs with coilovers

So... first picks into front upper adjustable coilover towers

http://y.delfi.ee/orig/206585/11094183_XmiCpO.jpeg
http://y.delfi.ee/orig/206585/11094179_sLgnku.jpeg

And these parts will be bolted into whatever position - so I can use different shocks and lift or ... truck just with bolts :bannana:
http://y.delfi.ee/orig/206585/11094181_xWsG43.jpeg

:wave:

(EST)_MahviaDeTyrk

06-07-2011, 01:10 PM

Bolts made and painted :crazy:
http://y.delfi.ee/orig/206585/11441415_Vc5PaQ.jpeg

Also made plus 2'' anti reverse shackles for front
http://y.delfi.ee/orig/206585/11441449_lLfzyj.jpeg

And new tires arrived :bannana:
Belshina F-Bel 106M (12,4/16)
Real size is around 35'' (measured without wheel diameter 890mm)
1'' skid depth
compared on pick with my old Maxxis Mudzilla 33-13,5-15
http://y.delfi.ee/orig/209981/11441467_isdPhg.jpeg
more reading about them http://www.patrol4x4.com/forum/nissan-safari-31/belshina-f-bel-106m-tires-nissan-safari-36502/

:wave:

(EST)_MahviaDeTyrk

08-16-2011, 09:18 AM

More free space neede, and need to move rear axle littlebit back - so ...

marked (2'' up and 8'' back)
http://y.delfi.ee/orig/204561/11079609_bzJ7kO.jpeg

after cut and welding
http://y.delfi.ee/orig/204561/11911793_XnwVwT.jpeg

inside wiev
http://y.delfi.ee/orig/204561/11911795_z4DXZd.jpeg
http://y.delfi.ee/orig/204561/11911791_rAReB7.jpeg

:wave:

soccerbrace

08-16-2011, 01:35 PM

NICE!

(EST)_MahviaDeTyrk

08-29-2011, 11:51 AM

Just few side fotos to see how it's with 32'' and how it seems with 35'' (if I move rear axle 7'' back)
If I move rear axle 7'' back wheelbase = 100''

http://y.delfi.ee/orig/204561/11079609_bzJ7kO.jpeg
http://y.delfi.ee/orig/204561/12007559_xzVU5w.jpeg

:wave:

Chainsaw

08-29-2011, 12:23 PM

Are these new tires made for heavy equipment? Or for light truck? I just wonder if they are too stiff for/too many ply for a light vehicle like a patrol.

(EST)_MahviaDeTyrk

08-30-2011, 01:24 PM

Are these new tires made for heavy equipment? Or for light truck? I just wonder if they are too stiff for/too many ply for a light vehicle like a patrol.

they are tractor front axle tires = agree - they may bee too stiff - can be cutted
But I have seen they work well and self cleaning is exellent

(EST)_MahviaDeTyrk

12-24-2011, 11:04 AM

Cleaned all inside
http://y.delfi.ee/orig/204561/13302499_rxKlu8.jpeg
And out
http://y.delfi.ee/orig/204561/13302501_Scu6i0.jpeg
Waiting paintjob

Project "Let's make something cool"

Koni RAID series shock's (10'' Pin-Pin)
http://y.delfi.ee/orig/206585/13302525_MU66Sa.jpeg
Made end's into uniball
http://y.delfi.ee/orig/206585/13302527_ShTC3x.jpeg
http://y.delfi.ee/orig/206585/13302531_fIMRve.jpeg
http://y.delfi.ee/orig/206585/13302533_QJZtgz.jpeg
http://y.delfi.ee/orig/206585/13302535_ou0JRQ.jpeg
Continues ...

:wave:

(EST)_MahviaDeTyrk

01-02-2012, 01:57 PM

Stinless pipe

http://y.delfi.ee/orig/206585/13342693_auAJFj.jpeg
http://y.delfi.ee/orig/206585/13342695_RwovX1.jpeg

Seems coilover is coming :bannana:
http://y.delfi.ee/orig/206585/13342691_udnrfW.jpeg

continues
:wave:

(EST)_MahviaDeTyrk

05-14-2012, 04:56 AM

Small update

H233B 33 spline rear axle with factory locker (from Y60 Patrol)
http://pilt.delfi.ee/show.php?mode=0&id=11079615&salt=g0EfMn.jpeg

http://pilt.delfi.ee/show.php?mode=0&id=11079613&salt=HrfDjg.jpeg

Cleaned and ...
http://pilt.delfi.ee/show.php?mode=0&id=13302543&salt=57Ac5E.jpeg

:wave:

Allen Cox

05-14-2012, 11:16 AM

Is that a vacuum actuated locker? What's the width on that bad boy (wheel mounting surface to wheel mounting surface)?

I need some parts for my '66 Patrol, I wonder if I could get a deal on shipping if I ordered a bunch of stuff from down under.

(EST)_MahviaDeTyrk

05-15-2012, 09:01 AM

Is that a vacuum actuated locker?

Vacuum locker with membrane (can used with pressure too - no problem)

What's the width on that bad boy (wheel mounting surface to wheel mounting surface)?

Don't remember - need to measure (going to travel - can answer after 2 weeks)